Open Search

Resource library

Displaying 301 - 350 of 761

Motor Winding Temperature and Detectors to Measure It

Published: October 2013
Author: Tom Bishop, P.E., EASA Senior Technical Support Specialist
Recording duration: 46 minutes
Technical subject(s): AC motor cooling, Design/theory/application, Stators/windings, Temperature detectors
CLICK HERE TO PURCHASE

Common recommendations for stored motors

Published: September 2013
Author: Chuck Yung, EASA Senior Technical Support Specialist
Technical subject(s): Bearings, Form wound, Motor storage, Random wound

Let's Get Organized: Reduce Waste & Optimize Productivity

Published: September 2013
Author: Mike Howell, EASA Technical Support Specialist
Recording duration: 46 minutes
Technical subject(s): N/A
CLICK HERE TO PURCHASE

Removing an impeller threaded onto a pump shaft

Published: September 2013
Author: EASA Technical Support Staff
Technical subject(s): Pumps, Repair procedures and tips, Shafts

Social media isn't just for kids - it's for your business, too!

Published: September 2013
Author: Eddie Bluff & Brian Bluff, Site-Seeker, Inc.
Technical subject(s): N/A

The SELL Process: Pre-Call Planning

Published: September 2013
Author: Jerry Peerbolte, J. Peerbolte & Associates
Recording duration: 60 minutes
Technical subject(s): N/A
CLICK HERE TO PURCHASE

Working with hand tools

Published: September 2013
Author: EASA Technical Support Staff
Technical subject(s): Safety, Service center equipment

Benefits of the AC hi-pot for new form coil stator windings

Published: August 2013
Author: Mike Howell, EASA Technical Support Specialist
Technical subject(s): AC motors, Form wound, Motor testing, Testing

Measuring stator winding resistance

Published: August 2013
Author: EASA Technical Support Staff
Technical subject(s): N/A

Practical Problem Solving for the Entire Service Center

Published: August 2013
Author: Mike Howell, EASA Technical Support Specialist
Recording duration: 53 minutes
Technical subject(s): N/A
CLICK HERE TO PURCHASE

Safely use air, hydraulic tools

Published: August 2013
Author: EASA Technical Support Staff
Technical subject(s): Safety, Service center equipment

Determining if noise is air gap related

Published: July 2013
Author: EASA Technical Support Staff
Technical subject(s): N/A

Inspect welding equipment often

Published: July 2013
Author: EASA Technical Support Staff
Technical subject(s): Safety, Service center equipment

Revisando la corrección por temperatura de la resistencia de aislamiento

Published: July 2013
Author: Mike Howell, EASA Technical Support Specialist
Technical subject(s): AC motors, Motor testing, Winding insulation

Revisiting insulation resistance temperature correction

Published: July 2013
Author: Mike Howell, EASA Technical Support Specialist
Technical subject(s): AC motors, Motor testing, Winding insulation

Sistemas de calefacción para evitar daños en el motor por condensación

Published: July 2013
Author: Jim Bryan, EASA Technical Support Specialist
Technical subject(s): Space heaters

Space heating to prevent motor damage from condensation

Published: July 2013
Author: Jim Bryan, EASA Technical Support Specialist
Technical subject(s): Space heaters

Drip, drip, drip: Understanding O-rings in the repair process

Published: June 2013
Author: Gene Vogel, EASA Pump & Vibration Specialist
Technical subject(s): Pump seals, Pumps

Fundamentals of Pump Repair

Published: June 2013
Technical subject(s): Case studies, Design/theory/application, Pump testing, Pumps, Troubleshooting & failure analysis
CLICK HERE TO PURCHASE

Importance of using micrometer to measure magnet wire size

Published: June 2013
Author: EASA Technical Support Staff
Technical subject(s): Service center equipment, Wire

Simple precautions when working with air and hydraulic tools

Published: June 2013
Author: EASA Technical Support Staff
Technical subject(s): Safety, Service center equipment

The winding challenge — servo and spindle motors

Published: June 2013
Author: Tom May, Trade-Mark Industrial
Technical subject(s): Servo motors

Vibration of Belt Driven Machines

Published: June 2013
Author: Gene Vogel, EASA Pump & Vibration Specialist
Recording duration: 58 minutes
Technical subject(s): Base/soleplate/foundation, Sheaves/pulleys/belting, Troubleshooting & failure analysis, Vibration
CLICK HERE TO PURCHASE

Connections on AC electric motors under 600 volts

Published: May 2013
Author: Anthony Sieracki, Spina Electric Co.
Technical subject(s): AC motors, Stators/windings

Drilling Down Into DC Design

Published: May 2013
Author: Chuck Yung, EASA Senior Technical Support Specialist
Recording duration: 64 minutes
Technical subject(s): DC motors, Design/theory/application, Repair procedures and tips
CLICK HERE TO PURCHASE

Properly surge testing armature depends on consistency of winding

Published: May 2013
Author: EASA Technical Support Staff
Technical subject(s): Armatures, Motor testing

Special care when lifting material

Published: May 2013
Author: EASA Technical Support Staff
Technical subject(s): Safety

Squirrel cage motors: Three most common starting methods

Published: May 2013
Author: Tom Bishop, P.E., EASA Senior Technical Support Specialist
Technical subject(s): AC motors, Design/theory/application, Stators/windings, Winding connections

Flashover: Causes and cures for damage to brushholders, commutators

Published: April 2013
Author: Chuck Yung, EASA Senior Technical Support Specialist
Technical subject(s): Armatures, Brushes, Commutators, DC motors, Troubleshooting & failure analysis

Push, don't pull when using hoist, crane

Published: April 2013
Author: EASA Technical Support Staff
Technical subject(s): Cranes/hoists, Safety

Special care when removing rotor in permanent magnet motors

Published: April 2013
Author: EASA Technical Support Staff
Technical subject(s): Rotors

Trials and tribulations of split case pump seals

Published: April 2013
Author: Bret McCormick, Stewart's Electric Motor Works, Inc.
Technical subject(s): Pump seals, Pumps

Enhance Your Market Position Using EASA's Recommended Practices

Published: March 2013
Author: Jerry Peerbolte, J. Peerbolte & Associates
Recording duration: 51 minutes
Technical subject(s): N/A
CLICK HERE TO PURCHASE

Stator I2R loss: Considerations for rewinds and redesigns

Published: March 2013
Author: Mike Howell, EASA Technical Support Specialist
Technical subject(s): AC motors, Design/theory/application, Stators/windings

Tech Tip: Winding change considerations

Published: March 2013
Author: EASA Technical Support Staff
Technical subject(s): Design/theory/application, Stators/windings

Use the right tool

Published: March 2013
Author: EASA Technical Support Staff
Technical subject(s): Safety, Service center equipment

Considerations for selecting an adjustable speed drive in a constant torque application

Published: February 2013
Author: Bill Colton, Baldor Electric Co., A Member of the ABB Group
Technical subject(s): Design/theory/application, Drives/controls

Keep work area clean and orderly

Published: February 2013
Author: EASA Technical Support Staff
Technical subject(s): Safety

Repair Tips for Submersible Pumps

Published: February 2013
Author: Gene Vogel, EASA Pump & Vibration Specialist
Recording duration: 63 minutes
Technical subject(s): Pump seals, Pump testing, Pumps, Repair procedures and tips
CLICK HERE TO PURCHASE

Slot liner insulation

Published: February 2013
Author: EASA Technical Support Staff
Technical subject(s): Winding insulation

Understanding end play and its impact on axial alignment

Published: February 2013
Author: Jim Bryan, EASA Technical Support Specialist
Technical subject(s): Alignment

We found out there is a friendlier side of OSHA

Published: February 2013
Author: Janet Schmidlkofer, K&N Electric Motors, Inc.
Technical subject(s): Safety

Converting vibration units not difficult if data is available

Published: January 2013
Author: Gene Vogel, EASA Pump & Vibration Specialist
Technical subject(s): Design/theory/application, Vibration

Easy steps to improve quality at your service center

Published: January 2013
Author: Charles Bailey, EASA Technical Education Committee
Technical subject(s): N/A

Handling Partial Discharge Issues

Published: January 2013
Author: Chuck Yung, EASA Senior Technical Support Specialist
Recording duration: 61 minutes
Technical subject(s): AC motors, Design/theory/application, Repair procedures and tips, Stators/windings
CLICK HERE TO PURCHASE

Redesign to change motor design letter designation

Published: January 2013
Author: EASA Technical Support Staff
Technical subject(s): N/A

Some simple precautions to take when working on a ladder

Published: January 2013
Author: EASA Technical Support Staff
Technical subject(s): Safety

Determining if a motor is running hot

Published: December 2012
Author: EASA Technical Support Staff
Technical subject(s): N/A

Fire prevention

Published: December 2012
Author: EASA Technical Support Staff
Technical subject(s): Safety

Motor Lubrication Cautions & Tips

Published: December 2012
Author: Jim Bryan, EASA Technical Support Specialist
Recording duration: 63 minutes
Technical subject(s): AC motors, Bearings, DC motors, Lubrication
CLICK HERE TO PURCHASE

Pages