Open Search

Resource library

Displaying 1 - 30 of 164

Safety Tip: What not to wear

Published: January 2019
Technical subject(s): Safety

Tech Tip: Use C4 bearing when heat is a factor

Published: January 2019
Technical subject(s): Bearings

Measuring stator core dimensions for core test with windings installed

Published: November 2018
Technical subject(s): Motor testing, Stators/windings

Safety Tip: Drivers’ Ed - A quick refresher on responsible driving practices

Published: October 2018
Technical subject(s): Safety, Service center equipment

Tech Tip: Pulley eccentricity

Published: October 2018
Technical subject(s): Sheaves/pulleys/belting

Safety Tips: The “eyes” have it: Tips to protect your eyes from hazards in the service center

Published: September 2018
Technical subject(s): Safety

Tech Tip: VFDs sitting around?

Published: September 2018
Technical subject(s): Drives/controls

Safety Tips: Summer precautions

Published: July 2018
Technical subject(s): Safety

Tech Tip: Magnetic wedges

Published: July 2018
Technical subject(s): Stators/windings

Tech Tip: Possible cause of failure in high-speed winding

Published: June 2018
Technical subject(s): Cranes/hoists, Stators/windings, Troubleshooting & failure analysis

Safety tips for personal and respiratory protection

Published: May 2018
Technical subject(s): Safety, Service center equipment

Tech Tip: Estimating copper weight

Published: May 2018
Technical subject(s): Repair procedures and tips, Stators/windings, Wire

Safety Tips: Machinery cautions

Published: April 2018
Technical subject(s): Safety, Service center equipment

Tech Tip: Submersibles – oil filled stator?

Published: April 2018
Technical subject(s): Lubrication, Stators/windings

Safety Tips: Rules for the machine shop

Published: March 2018
Technical subject(s): Safety, Service center equipment

Tech Tip: Consider cost when selecting pump seal

Published: March 2018
Technical subject(s): Pump seals, Pumps

General rules and precautions when using grinders

Published: January 2018
Technical subject(s): Safety, Service center equipment

Interpreting results of armature surge test

Published: January 2018
Technical subject(s): Armatures, Motor testing

Effect of adjustable speed drive carrier frequency on bearing current

Published: December 2017
Technical subject(s): AC motors, Design/theory/application, Drives/controls

Tech Tip: Key points when performing stator core loop test

Published: November 2017
Technical subject(s): Laminations, Motor testing, Stators/windings, Winding insulation

Troubleshooting DC field temperature issues

Published: October 2017
Technical subject(s): DC motor cooling, Field coils, Nameplates, Repair procedures and tips, Ventilation/cooling

Burnout oven calibration

Published: August 2017
Technical subject(s): Repair procedures and tips, Service center equipment

Rotor bar pass frequencies

Published: June 2017
Technical subject(s): Motor testing, Rotors, Vibration

Tech Tip: Novel method for packing a bearing with grease

Published: April 2017
Author: Bret McCormick, Stewart’s Electric Motor Works, Inc., Orlando, Florida, Technical Education Committee Member
Technical subject(s): Bearings, Grease lubrication, Lubrication

Tech Tips: Tips for motor paint

Published: April 2017
Technical subject(s): Miscellaneous, Repair procedures and tips

Safety Tips: Remember these general rules

Published: March 2017
Technical subject(s): Miscellaneous, Safety

Tech Tip: When restacking, use real coreplate

Published: March 2017
Technical subject(s): Repair procedures and tips

Simple tips for important electrical tests

Published: February 2017
Technical subject(s): AC motors, Motor testing, Stators/windings

Off-the-job safety

Published: January 2017
Technical subject(s): Safety

Unequal grouping sequences for 
1-4 vs. 1-7 jumpers

Published: January 2017
Technical subject(s): Stators/windings

Pages