Open Search

Resource library

Displaying 1 - 30 of 35

Bobinage d'un stator triphasé

Published: September 2016
Recording duration: 10 hours
Technical subject(s): AC motors, Motor testing, Nameplates, Random wound, Repair procedures and tips, Service center equipment, Stators/windings, Training, Winding connections, Winding insulation, Wire
CLICK HERE TO PURCHASE

Procédure simple de dépannage d'amplificateurs sur le terrain

Published: October 2012
Author: Bill Colton, Baldor Electric Co., A Member of the ABB Group
Technical subject(s): Drives/controls, Motor testing, Troubleshooting & failure analysis

Essai des rotors à cage d'écureuil

Published: September 2012
Author: Tom Bishop, P.E., EASA Senior Technical Support Specialist
Technical subject(s): AC motors, Motor testing, Rotors

Conversions d'enroulement concentrique à imbriqué/imbriqué à concentrique

Published: April 2011
Author: Chuck Yung, EASA Senior Technical Support Specialist
Technical subject(s): AC motors, Design/theory/application, Winding connections

Pièges (potentiels) des circuits montés en parallèle

Published: December 2010
Author: Cyndi Nyberg Esau, Former EASA Technical Support Specialist
Technical subject(s): AC motors, Design/theory/application, Winding connections

Servocommandes

Published: June 2009
Author: Bill Colton, Baldor Electric Co., A Member of the ABB Group
Technical subject(s): Servo motors

Guide d’approvisionnement en bobines préformées pour moteurs et génératrices

Published: June 2008
Author: Manuel Garcia, Jr., Consultant, Rotating Electrical Machines
Technical subject(s): AC motors, Alternators/generators, Form wound

Fabrication et installation d’un nouvel arbre de moteur

Published: September 2006
Author: Tucker Woodson, Rockwell Automation
Technical subject(s): Design/theory/application, Repair procedures and tips, Shafts

Amplificateurs MLI

Published: October 2003
Author: Bill Colton, Baldor Electric Co., A Member of the ABB Group
Technical subject(s): AC motors, DC motors, Drives/controls

Analyse de l’arbre des moteurs électriques

Published: October 2003
Author: E. Steve Darby (deceased), Darby Electric Co.
Technical subject(s): Repair procedures and tips, Shafts

Assurer l’intégrité mécanique des moteurs électriques

Published: October 2003
Author: L. Douglas Berry (deceased), Diagnostic Technologies, Inc.
Technical subject(s): Bearings, Lubrication, Repair procedures and tips, Shafts

Cause et analyse des défaillances de paliers antifriction dans les moteurs à induction ca

Published: October 2003
Author: Austin Bonnett, EASA Education & Technology Consultant
Technical subject(s): Bearings, Lubrication, Troubleshooting & failure analysis

Cause et analyse des défaillances de paliers et d’arbres de moteurs électriques

Published: October 2003
Author: Austin Bonnett, EASA Education & Technology Consultant
Technical subject(s): Bearings, Troubleshooting & failure analysis

Causes et analyse des défaillances de stators et de rotors des moteurs à induction à courant alternatif

Published: October 2003
Author: Austin Bonnett, EASA Education & Technology Consultant
Author: George C. Soukup, U.S. Electric Motors, a Division of Emerson Electric
Technical subject(s): AC motors, Rotors, Stators/windings, Troubleshooting & failure analysis

Comment prendre les mesures des moteurs et génératrices à enroulement

Published: October 2003
Author: Manuel Garcia, Jr., Consultant, Rotating Electrical Machines
Technical subject(s): Form wound, Repair procedures and tips

Dépannage sur place d’un moteur à courant continu

Published: October 2003
Technical subject(s): DC motors, Troubleshooting & failure analysis

Directives pour maintenir le rendement d’un moteur durant sa remise en état

Published: October 2003
Technical subject(s): AC motors, Laminations, Motor testing, Repair procedures and tips, Stators/windings

Données relatives aux fils de bobinage circulaires

Published: October 2003
Technical subject(s): Wire

Essai des rotors à cage d’écureuil

Published: October 2003
Technical subject(s): AC motors, Cast rotors, Fabricated rotors, Motor testing, Rotors

Facteurs à considérer pour l’utilisation d’inverseurs à modulation d’impulsions en durée et de moteurs ca à induction à l’intérieur d’un système complet

Published: October 2003
Author: Austin Bonnett, EASA Education & Technology Consultant
Technical subject(s): AC motors, Design/theory/application, Drives/controls

Facteurs de conversion de bobinage concentique á bobinage imbriqué

Published: October 2003
Technical subject(s): AC motors, Stators/windings, Winding connections

Installation de bandes de fibre de verre pré-imprégnées sur un induit

Published: October 2003
Author: Chuck Yung, EASA Senior Technical Support Specialist
Technical subject(s): Armatures, Repair procedures and tips

La fabrication d’arbres de rechange pour moteurs électriques

Published: October 2003
Author: E. Steve Darby (deceased), Darby Electric Co.
Technical subject(s): Repair procedures and tips, Shafts

Le rebobinage de moteurs EVV

Published: October 2003
Author: Richard Huber, P. Eng., Richard Huber Engineering, Ltd.
Technical subject(s): AC motors, Drives/controls, Repair procedures and tips

Les enroulements intercalaires: que sont-ils?

Published: October 2003
Author: Chuck Yung, EASA Senior Technical Support Specialist
Technical subject(s): AC motors, Design/theory/application, Stators/windings, Winding connections

Lubrification des roulements des machines électriques

Published: October 2003
Technical subject(s): Ball bearings, Grease lubrication, Lubrication, Lubrication compatibility, Oil lubrication, Roller bearings

Normes relatives à l’équilibrage dynamique

Published: October 2003
Author: John Harrell, On-Site Training Services
Technical subject(s): Balancing

Paliers de butée antifriction pour moteurs verticaux

Published: October 2003
Author: Austin Bonnett, EASA Education & Technology Consultant
Technical subject(s): AC motors, Bearings, Repair procedures and tips

Porte-balais (ou supports) et performances des balais de carbone (ou brosses)

Published: October 2003
Author: Jeff D. Koenitzer, P.E., Helwig Carbon Products, Inc.
Technical subject(s): Brushes, DC motors, Design/theory/application

Procédés de vérification des jeux axiaux dans les dispositifs à roulements

Published: October 2003
Author: Chuck Yung, EASA Senior Technical Support Specialist
Technical subject(s): Ball bearings, Repair procedures and tips, Testing

Pages